I delete the old traffic-services config, after cleaning and FBS configs existing ports, prior to creating the FBS cos-mappings, but old configs still appear afterwards.

DELETE actions:

!delete

!traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 1 dot1dpri-dei 0 r-cos 2 r-color green

!traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 4-5 dot1dpri-dei 0 r-cos 3 r-color green

!then create

traffic-services cos-mapping resolved-cos-map delete cos-map FBS-FcosRcos

!

traffic-services cos-mapping resolved-cos-map create cos-map FBS-FcosRcos

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 0 dot1dpri-dei 0 r-cos 0 r-color yellow

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 0 dot1dpri-dei 1 r-cos 0 r-color yellow

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 1-2 dot1dpri-dei 0 r-cos 2 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 3-5 dot1dpri-dei 0 r-cos 3 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 6 dot1dpri-dei 0 r-cos 4 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 7 dot1dpri-dei 0 r-cos 6 r-color green

!

CONFIG afterwards:

traffic-services cos-mapping resolved-cos-map create cos-map FBS-FcosRcos

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 0 dot1dpri-dei 0 r-cos 0 r-color yellow

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 0 dot1dpri-dei 1 r-cos 0 r-color yellow

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 1 dot1dpri-dei 0 r-cos 2 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 4-5 dot1dpri-dei 0 r-cos 3 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 6 dot1dpri-dei 0 r-cos 4 r-color green

traffic-services cos-mapping resolved-cos-map set cos-map FBS-FcosRcos dot1dpri-cos 7 dot1dpri-dei 0 r-cos 6 r-color green

!

Hi Frederick Valcho

Apologies for the response/delay.

I spent a number of hours in the lab replicating your scenario and experienced the same result.

To make it simple, I created a simple r-cos mapping as shown below:

But the output was the same, after saving the configuration

Why ?????

Well that's because the default cos-mapping configuration has already defined dot1dpri-cos 3 as r-cos 3 r-color green and therefore is not required to be shown in your custom cos-mapping.

The same result occurs if you tried to configure dot1dpri-cos 2 as r-cos 2 r-color green. The default mapping has already defined these values.

If I used the change the configuration to this:

r-cos 2r-color greenThen the traffic-services configuration would be present for the custom cos-map.

I hope that explains it for you.

Please advise.

Thanks

Brett